Tips & Tutorials

Root XXUDOJ3 Android 5.1.1 Lollipop on Galaxy Note 10.1 P600 KitKat Stock Firmware

Once you have updated your Samsung Galaxy Note 10.1 to XXUDOJ3 Android 5.1.1 Lollipop firmware, you can root it by following this post. XXUDOJ3 Android 5.1.1 Lollipop firmware is a major update for this tablet as it was previously running Android 4.4.2 KitKat. Almost everything has been changed and tweaked. However, once you update to this firmware, your previous root status will be lost. You would have to root your tablet once again in order to enjoy all of it’s features. Gladly, Samsung devices generally have an easier root method and Galaxy Note 10.1 P600 is no exception. Never tried rooting before? read: Benefits of rooting an Android device. You can now root XXUDOJ3 Android 5.1.1 on Galaxy Note 10.1 P600 official firmware using the tutorial below. Please carefully read all the steps before actually performing it on your tablet.

As you read further, we will guide you through the entire process of how to root Galaxy Note 10.1 SM-P600 on XXUDOJ3 Android 5.1.1 Lollipop official firmware. Right now, there are two main ways to root: ClockworkMod recovery (CWM) method or ODIN can be used. We prefer the ODIN method because it is very easy to perform and quickly roots your device. It is not really necessary, but please make sure you backup your tablet as a precaution and also read all the important tips given below before proceeding to the tutorial. Read our list of the essential root apps available! Let’s continue below to the tutorial.

Root Galaxy Note 10.1 SM-P600

Disclaimer: All the custom ROMs and firmwares, official software updates, tools, mods or anything mentioned in the tutorial belong to their respective owners/developers. We (TeamAndroid.com) or the developers are not to be held responsible if you damage or brick your device. We don’t have you on gun point to try out this tutorial 😉

Root XXUDOJ3 Android 5.1.1 on Galaxy Note 10.1 – CF-Auto-Root:

For those who do not know about CF-Auto-Root:

CF-Root is the root for “rooting beginners” and those who want to keep as close to stock as possible. CF-Root is meant to be used in combination with stock Samsung firmwares, and be the quickest and easiest way for your first root. A modified recovery and cache partition will be flashed, which will install (only) SuperSU, then clean-up the cache partition and re-flash the stock recovery.

NOTE: Using this root increases your flash counter. You should run Triangle Away after rooting to reset the counter. Note that if you want to run custom kernels or custom recoveries, your flash counter will be set to 1 at every boot. Either configure Triangle Away to reset the counter at every boot (Play version only) or only reset the counter when you need to go into warranty.

You might want to read the following articles:

Samsung Galaxy Note 10.1 USB Drivers

You will need to connect your Android tablet with the computer. For that, please make sure you have installed the Android 5.1.1 USB drivers for Samsung Galaxy Note 10.1 properly. If not, you can download the latest official drivers from our Android USB Drivers section here:

Download Samsung Galaxy Note 10.1 USB drivers!

Backup and Other Important Tips

Done with the USB drivers? Perfect. The tutorial is on the next page, but first, please take a look at the following tips and important points you need to take care of. These are important, as we don’t want anyone losing their personal data or apps:

Always backup your important data that you might need after you install a new custom ROM, an official software update or anything else. Make a backup for just in case, you never know when anything might go wrong. See below for some tips on how to backup data:

Samsung users can also back up data using Samsung KIES. If you backup data manually, you get more options what to choose from and it is very easy to move data across Android devices from different manufacturers, i.e moving Samsung Galaxy Note backup data to HTC One X.

If you already have a custom recovery (ClockworkMod, TWRP etc.) installed on your tablet, we strongly recommend you to also backup using that as it creates a complete image of your existing tablet set up.

A few more optional tips that you should remember:

1. Having problems connecting your Android tablet to the computer? You need to enable USB debugging mode. See here: How to Enable USB Debugging — for Gingerbread, Ice Cream Sandwich, Jelly Bean and Lollipop.

2. Make sure your Android device is charged up to 80-85% battery level. This might help you: How to Check Battery Percentage. Why? Because, if your tablet goes off suddenly while installing a custom ROM, flashing an official firmware update or installing mods etc. — your tablet might get bricked or go dead permanently. No one wants that, right?

4. Most of the tutorials and how-to guides on Team Android are for factory unlocked Android phones and tablets. We recommend NOT to try our guides if your tablet is locked to a carrier, unless we have specified the carrier name or device model.

If you find the above tips useful and they were helpful to you, please consider giving us a +1 or LIKE to thank us!

All set and ready? Good. Now, let’s proceed with the tutorial on the next page and root Galaxy Note 10.1 P600 on XXUDOJ3 Android 5.1.1 Lollipop official firmware.

About the author

Taimur Akmal

Devoted writer, enjoys developing code. Appreciates excellent food, exceptional coffee and great company. He is also into sublime design and nicely built cars.

15 Comments

          • They deleted my comment apparently. Give a bad method and then destroy any chance of people finding out correct procedure. Great website.

            First, flash the ROM(of course).

            You have to find the 2.52 Super SU (i believe its beta) for the P600. Then search for the custom boot.IMG for p600 available in the xda forums. Flash both of these with odin. This should fix bootloop and give you root.

          • I have never rooted a device before. Is there a link that you know of that would take me through the step by step instructions of rooting my p600? I thought I would follow the team android method but too many people are having problems with it..

          • No honestly. What device do you have? If it’s the p600(2014 note 10.1) then just Google “root p600”. Go into device settings, about device to find model #. Just beware, rooting is a bit sketchy for noobs. It’s nervracking and if you don’t do your research you can make mistakes. Everybody has to start somewhere though.

  • I tried it too and the same thing happened to me… This is not the proper way to Root… I tried kingroot and kingoroot and they don’t work either!!!!

    • I know…write a crappy article and then dont update it. Sorry author.
      Find the custom boot.img on xda developers. Flash that. Then flash the beta su 2.52 for the p600. That should get you out of boot loop. That’s what I had to do. Let me know if you have trouble finding it and I’ll post link.

  • Upgraded to DOJ3 fine and when ran Odin for rooting it appeared to do fine. But at reboot I got the error: “Recovery is not seandroid enforced” and got stuck in a back and forth boot loop between the “Samsung” Logo and the “Samsung Galaxy Note 10.1 2014 Edition” start screen. Any success in rooting by anyone?? if so, what and how did you do it?

  • the same boot loop!!! and the same message “Recovery is not Seandroid Enforcing”, so can you give us a guide of the process for solving the problem ?? and the links with the files you mentioned? Thanks, the rom works fine but I need the device rooted.

  • for anyone trying to figure out if this works,if you are using a stock rom (like everyone on their first try), this WILL NOT work unless you first install SUPERSU and TWRP with Odin…

Leave a Comment